-
B.A.T PVC Waterproofing AngleVendor:B.A.TB.A.T PVC Waterproofing Angle is a white PVC angle profile used to form a defined barrier at the edge of wet-area waterproofing systems. Although it is a plastic angle by material, its intended role is waterproofing termination rather than structural framing, general corner protection...
- From $18.67
- From $18.67
- Unit price
- per
-
Anodized Aluminum Balcony Drip Angle (12mm x 3m)Vendor:B.A.TB.A.T 12 mm Anodised Aluminium Balcony Drip Angle is a 3 m balcony drip edge for tiled or rendered balcony perimeters. The projecting drip lip directs runoff clear of the fascia, cladding or render below instead of allowing water to track back underneath the...
- From $21.96
- From $21.96
- Unit price
- per
-
B.A.T Bright Steel Square Notch TrowelVendor:B.A.TA square notch trowel for ceramic, porcelain, and stone adhesive beds. The square notch combs full ribs that collapse evenly under the tile, which is what pushes air out and coverage up.Bright steel blade, sizes from 4mm to 12mm. Match the notch to the...
- $25.00
$0.00- $25.00
- Unit price
- per
-
BAT Pro Surface Protection MatVendor:B.A.TA protective mat for working over finished surfaces. Lay it across floors, benchtops, and cabinetry while the job runs, and spills, scuffs, and dropped tools mark the mat instead of the client's house.Light enough to reposition as the work moves, tough enough to reuse...
- $108.33
- $108.33
- Unit price
- per
-
BAT Professional Stainless Steel TrowelVendor:B.A.TA stainless square notch trowel for tile adhesive beds, in notch sizes from 4mm to 15mm. Pick the size the adhesive datasheet calls: the notch sets how much adhesive goes down, and coverage is where bond failures start.Stainless shrugs off cement mortars and will...
- $29.17
$0.00- $29.17
- Unit price
- per
-
BAT Pro Gauging Trowel with Swan NeckVendor:B.A.TA small trowel for moving adhesive and grout from bucket to bed or hawk. The carbon steel blade is stiff enough to scoop dense materials without flexing, and the pointed shape loads a clean cut of mix.The swan neck in the handle hooks over...
- From $12.50
- From $12.50
- Unit price
- per
-
BAT PRO Square Trowel With Swan NeckVendor:B.A.TA flat square trowel for laying tile adhesive to an even bed. The steel blade holds its edge against abrasive mortars, and an even bed is what stops lippage and hollow spots under the tile.The swan neck hooks over the bucket rim between loads...
- From $12.50
- From $12.50
- Unit price
- per
-
BAT Bright Steel Trowel V NotchVendor:B.A.TA V-notch trowel for laying adhesive at the spread rate the manufacturer asks for. The notch size sets how much adhesive goes down: pick the size your adhesive datasheet calls, then hold a consistent angle and the ribs come out even.Available in 3mm, 5mm,...
- $28.25
$0.00- $28.25
- Unit price
- per
-
Premium Pointed Rubber Grouter – Japanese RubberVendor:B.A.TThis grouter does the same job as the BAT Trade Quality pointed grouter: grouting corners and narrow joints. The difference is the blade. Japanese rubber is softer and more flexible, so it holds an edge longer and gives a smoother finish on soft or...
- $40.50
- $40.50
- Unit price
- per
-
BAT Pointed Grouter Trade QualityVendor:B.A.TA pointed rubber grouter pushes grout into corners and narrow joints where a flat float cannot reach. The BAT Trade Quality model has a pointed rubber blade and a timber handle. Work it along the joint to compact the grout, then strike off the...
- $21.08
- $21.08
- Unit price
- per
-
B.A.T Pro Folding Utility KnifeVendor:B.A.TA folding utility knife for membrane work and site prep. Score waterproofing membranes, trim expansion joint filler, cut backing rod, and open packaging; the blade tracks true under load, so cuts stay where you put them.The aluminium body folds shut to pocket size, and...
- From $16.20
- From $16.20
- Unit price
- per
-
BAT Trims Tile CrossesVendor:B.A.TKeep grout joints even and tiled layouts looking sharp with B.A.T Tile Crosses. These cross-shaped plastic spacers help maintain consistent gaps between tiles as you set out walls, floors and feature areas.Choose from 1.5 mm, 2 mm and 3 mm nominal joint sizes. Smaller...
- From $3.17
- From $3.17
- Unit price
- per
-
BAT Heavy Duty Paint Roller FrameVendor:B.A.TA 230mm heavy duty roller frame for big wall and ceiling areas. The reinforced steel cage holds its alignment under heavy pressure, so the film goes down even instead of thin at the ends of the stroke.Threaded handle for extension poles, ergonomic grip for...
- From $8.20
- From $8.20
- Unit price
- per
-
BAT Pro Electric Hand Mixer – 1600WVendor:B.A.TThe 1600W step up: a hand mixer for heavy material that stalls smaller mixers. Triple reduction gearing gives strong low-end torque, and the two speed ranges (0-380 and 0-660 RPM) let you crawl through dense compounds without whipping air into them. Use it for...
- $270.83
- $270.83
- Unit price
- per
-
BAT Trims EM1600P Spare Liquid Stirrer – 140mm x 590mm x M14 ThreadVendor:B.A.TThe spare paddle for the BAT Pro 1600W electric mixer. The 140mm head moves more material per turn than the small paddle, matching what the bigger motor can push.M14 thread for hand-tight swaps, 590mm shaft for deep buckets.
- $29.83
- $29.83
- Unit price
- per
-
BAT Pro Electric Hand Mixer – 1050W T-Shape HandleVendor:B.A.TA 1050W electric hand mixer for buckets of adhesive, grout, plaster, and paint. The triple reduction gearbox turns motor speed into paddle torque, so mixes come out consistent without stalling or burning the tool. T-handle grip for control from both sides, two speed settings...
- $194.58
- $194.58
- Unit price
- per
-
BAT EM 1050P Spare Liquid Stirrer – 120mm x 590mm x M14 ThreadVendor:B.A.TThe spare paddle for the BAT Pro 1050W electric mixer. Paddles wear and bend on site; a spare in the van means a bent paddle costs minutes, not a day.120mm mixing head, 590mm shaft, M14 thread for fast swaps on the compatible mixer.
- $22.92
- $22.92
- Unit price
- per
-
Raimondi Whisk Style Liquid StirrerVendor:B.A.TA four-blade whisk mixer with a 140mm head for buckets of paint, plaster, adhesives, and liquid membranes. Steel construction, M14 thread to suit most mixing drills.The whisk style folds material from the bottom of the bucket upward, which mixes faster and entrains less air...
- $59.50
- $59.50
- Unit price
- per
-
4 Blade Whisk Mixer Hex ShaftVendor:B.A.TA four-blade steel whisk paddle for drill-driven mixing. Four blades pull the material through itself instead of spinning it in circles, so buckets of adhesive, plaster, or paint blend without dry pockets at the base.120mm head, 550mm shaft, 10mm hex shank for standard drill...
- $19.17
- $19.17
- Unit price
- per
-
Floor / Wall Scraper 125mmVendor:B.A.TA short-handled 125mm scraper for tight spaces: behind toilets, in cupboard corners, along skirting lines. Same replaceable blade idea as its bigger brothers, sized for one-handed control where the long pole cannot swing.500mm handle keeps your knuckles out of the mess.
- $38.08
- $38.08
- Unit price
- per
-
BAT Tilers and Slaters SpongeVendor:B.A.TA 300mm sponge for washing grout haze off tile and slate. The oversized face covers large-format work quickly, and the dense synthetic holds just enough water: wet enough to clean the joint, not so wet it washes the grout back out.It resists shredding on...
- $11.75
- $11.75
- Unit price
- per
-
BAT Eco SynSafe AcidVendor:B.A.TBAT Eco SynSafe Acid is an acid-based cleaning and surface-preparation product for suitable masonry and concrete applications, including removal of cementitious residues, grout haze and mineral build-up where the surface is compatible. It may also be used for concrete etching where the following coating...
- From $34.42
- From $34.42
- Unit price
- per
-
BAT Trims Tile WedgesVendor:B.A.TTile wedges adjust spacing where a cross will not fit. The taper runs from 5mm down to a fine point, so you slide one under a tile edge to lift it level or nudge two tiles apart to widen a joint. Pull them out...
- From $6.67
- From $6.67
- Unit price
- per
-
BAT Trim Chalk Line ReelVendor:B.A.TA chalk line for setting datum lines on floors and walls before tiling or laying out work. Snap a line where the grid starts and every tile or panel keys off one mark instead of drifting a few millimetres a row.The aluminium case takes...
- $25.92
- $25.92
- Unit price
- per
-
BAT Trim Chalk Line Refill - RedVendor:B.A.TChalk refill for the BAT Trim chalk line. Pour it in, shake to settle, and get back to snapping straight lines for tile layout, stud work, or slab setout.Fine chalk gives a crisp line that does not blow away on concrete; keep the bottle...
- $22.67
- $22.67
- Unit price
- per
-
Red
-
Blue
-
Raimondi Epoxy SpongeVendor:B.A.TA Raimondi cellulose sponge made for epoxy grout, where ordinary sponges either smear resin into a haze or gouge the joints. The dense natural cellulose lifts and holds the resin residue instead of smearing it, and the controlled density cleans the tile face without...
- $23.25
- $23.25
- Unit price
- per
-
BAT Knee PadVendor:B.A.TKnee pads for tiling, flooring, and any job that puts you down on hard floors for hours. Heavy-duty outer shell takes the abrasion; gel or foam padding takes the pressure. The straps adjust over work pants, and the non-slip face keeps the pad under...
- $38.92
- $38.92
- Unit price
- per
-
Double Sided Aluminium Angle x 3mVendor:B.A.TFinish exposed tiled edges and substrate returns neatly with B.A.T's Double Sided Aluminium Angle. Its two-sided profile provides two working face dimensions, making it a useful option where a conventional single-sided tile angle does not cover the required edge.Supplied in 3m lengths with a...
- From $27.09
- From $27.09
- Unit price
- per
-
Half Round Trim x 3mVendor:B.A.TGive exposed tile edges a rounded, finished appearance with B.A.T Half Round Trim. The curved aluminium profile protects the edge visually and provides a softer alternative to a square or L-shaped tile angle.This 3m trim is suited to appropriately detailed tiled bath hobs and...
- From $21.78
- From $21.78
- Unit price
- per
-
Brass Angle x 3mVendor:B.A.TB.A.T Brass Angle x 3m provides a distinctive metal edge profile for tiled corners and exposed tile terminations. Use it when the visible brass look is part of the design, rather than relying on the tile edge alone to create a finished junction.Choose from...
- From $154.58
- From $154.58
- Unit price
- per
-
B.A.T Geometric Aluminium Angle (Water Stop) – Bright Silver – 3mVendor:B.A.TGive exposed corners a clean, defined finish with the B.A.T Geometric Aluminium Angle in Bright Silver. This solid, non-perforated L-shaped aluminium profile comes in a full 3m length and is available in either 1.6mm or 3mm material thickness.Geometric aluminium angles are useful for construction...
- From $36.00
- From $36.00
- Unit price
- per
-
B.A.T Mosaic Corner Angle x 3m – Bright Silver Box Tile TrimVendor:B.A.TCreate a crisp square-edged finish around mosaic tiles, feature walls and tiled corners with the B.A.T Mosaic Corner Angle in Bright Silver. The aluminium box-style trim gives exposed edges a neat metallic outline while helping protect tile corners from knocks and chips.Designed for junctions...
- From $24.38
- From $24.38
- Unit price
- per
-
B.A.T Mosaic Corner Angle x 3m – Matt White Box Tile TrimVendor:B.A.TFinish mosaic and feature-tile corners with a clean, understated square edge using the B.A.T Mosaic Corner Angle in Matt White. The aluminium box-style trim helps protect vulnerable tiled edges while blending naturally into white or pale-coloured tile schemes.This profile is designed for corners where...
- From $21.60
- From $21.60
- Unit price
- per
-
B.A.T Aluminium Diminishing Trim x 3m – Mill Finish – 15mmVendor:B.A.TCreate a smoother transition from a raised tiled floor to a lower adjoining surface with the B.A.T Aluminium Diminishing Trim. Its sloping profile reduces the abrupt exposed edge between floor finishes and gives the junction a neat, practical appearance.The 15mm profile in Mill Finish...
- $28.30
- $28.30
- Unit price
- per
-
B.A.T BATEX Aluminium Expansion Joint – Grey – 3mVendor:B.A.TProtect the edges of a designated tiled movement joint with the B.A.T BATEX Aluminium Expansion Joint. The 3 m aluminium profile frames a flexible grey centre, giving the tiled surface a neat finish while leaving the joint free to perform as designed.Choose the 11...
- From $101.17
- From $101.17
- Unit price
- per
-
B.A.T Aluminium Angle x 3m – Bright GoldVendor:B.A.TB.A.T Aluminium Angle x 3 m – Bright Gold is an L-shaped aluminium tile trim that protects an exposed tile edge while adding a bright gold decorative finish. The perforated fixing leg beds into tile adhesive, and the visible edge helps protect the cut...
- $17.70
- $17.70
- Unit price
- per
Frequently Asked Questions
What is an L-shaped perforated tile angle used for?
It forms a straight, protected edge where tile meets tile or tile meets another surface. The perforated leg embeds in the adhesive; the visible leg caps the edge.
Which finishes do BAT tile angles come in?
Mill finish, brushed silver, matt silver, bright silver, gloss black, matt black, gunmetal, pearl white, matt white, brushed gold, antique bronze, and linished stainless. Cut with a fine-tooth saw and deburr before you set it in the bed.
How do I choose the right tile angle depth?
Match it to your tile thickness plus adhesive bed. The visible leg should sit flush with or just under the tile face so grout lines read cleanly.
Can expansion joint trim be tiled over?
Yes. BAT expansion joint trim sits in the joint with its soft centre exposed, so movement is absorbed while the tiled edges stay protected. Cut with a fine-tooth saw and deburr before you set it in the bed.
What is a diminishing tile angle for?
It transitions between tiles of different thicknesses, such as floor to wall or a thick paver to a thin mosaic, without a stepped edge. Cut with a fine-tooth saw and deburr before you set it in the bed.