Tile crosses set the grout gap between wall tiles. Push one into each junction as you lay, and every line comes out the same width. When the adhesive has set, either tap them in and grout over, or pull them out and fill the gap.
Available in 1.5mm, 2mm, and 3mm thicknesses. Pack sizes: 500, 1,000, or 2,000 pieces. As a rule of thumb, allow 25 to 35 crosses per square metre depending on tile size.
They suit straight and diagonal wall layouts, and work with any tile adhesive. No primer, no cure time: they are spacers, not chemistry.
Frequently asked questions
Can these tile crosses be reused?
Yes, BAT Trims Tile Crosses can often be reused. Remove them before the tile adhesive fully cures and clean any adhesive residue thoroughly to maintain consistency.
Are BAT Trims Tile Crosses suitable for floor tiling?
These tile crosses are primarily designed for wall tiling. For floor tiling or larger format, heavier tiles, a dedicated tile levelling system is usually more appropriate to manage weight and flatness.
How many tile crosses are needed per square metre?
The quantity depends on your tile size and layout. For standard wall tiles in a straight pattern, expect to use approximately 25–35 spacers per square metre.
Can these be used for diagonal tile patterns?
Yes, BAT Trims Tile Crosses are effective for both straight and diagonal tile layouts. They provide consistent spacing and alignment across angled installations.
Applications and benefits
| Application | Key benefit | Primary trades |
|---|---|---|
| Bathroom and kitchen wall tiling | Maintains consistent grout lines for a clean, professional finish in wet areas. | Tilers, Builders |
| Feature walls and splashbacks | Ensures even tile spacing and alignment across visible surfaces. | Tilers, Renovators |
| Commercial interior wall tiling | Supports accurate installation and reduces rework on large-scale projects. | Commercial Tilers, Project Managers |
How to apply BAT Trims Tile Crosses:
- Spread tile adhesive on the wall using a notched trowel suitable for your tile size.
- Place your first tile and insert BAT Trims Tile Crosses at each corner or along edges depending on tile size.
- Continue placing tiles and crosses in alignment, checking with a spirit level as you go.
- For diagonal layouts, place spacers at 45° orientation and adjust for overlap if required.
- Remove crosses before grout is applied, ideally once adhesive has set but before full cure.
Product limitations
- Not for: Irregular stone or tiles with significant natural edge variation. Wedge spacers are better suited for these applications.
- Limited use: In floor tiling unless combined with tile levelling clips to manage tile weight and flatness.
- Not a substitute for: Levelling systems when flatness is critical across large-format tiles.
Safety and handling
BAT Trims Tile Crosses are made from inert plastic and are non-hazardous under normal use. Safety guidance pertains to general tiling practice and associated materials.
Personal protective equipment
Gloves are recommended for prolonged use, especially when handling tile adhesives. Safety glasses are advisable during tile cutting or other related tasks.
Ventilation
Ensure adequate ventilation when working with tile adhesives and grouts, as these materials may contain volatile components. The spacers themselves are inert and do not require specific ventilation.
First aid
- Skin contact: In case of skin contact with tile adhesive, rinse thoroughly with water. Refer to the tile adhesive's Safety Data Sheet for specific first aid measures.
- Ingestion/Eye contact: Unlikely. If product splinter enters eye, flush with water. If swallowed, seek medical advice.
Storage and disposal
Store BAT Trims Tile Crosses away from direct sunlight and heat sources to maintain plastic strength. Dispose of used or damaged spacers with general construction waste.
Substrate guide
Consistent tile spacing relies on correct substrate preparation, regardless of the tile type.
Ceramic wall tiles
Surface prep: Ensure surfaces are clean, dry, and structurally sound before tiling. Remove any dust, grease, or loose material.
Primer: Not required for the tile crosses themselves. Use appropriate primer for the substrate as per tile adhesive manufacturer's instructions.
Porcelain wall tiles
Surface prep: Ensure surfaces are clean, dry, and structurally sound before tiling. Remove any dust, grease, or loose material.
Primer: Not required for the tile crosses themselves. Use appropriate primer for the substrate as per tile adhesive manufacturer's instructions.
Calibrated stone wall tiles
Surface prep: Ensure surfaces are clean, dry, and structurally sound before tiling. Remove any dust, grease, or loose material. Verify stone is calibrated to minimise edge variation.
Primer: Not required for the tile crosses themselves. Use appropriate primer for the substrate as per tile adhesive manufacturer's instructions.
BAT Trims Tile Crosses Physical Properties
| Property | Value |
|---|---|
| Material | Polypropylene |
| Chemical Composition | Non-reactive, Adhesive-Resistant |
| Colour | White |
| Application Temperature Range | -10°C to 50°C |
| Coverage Rate | 25–35 spacers per m² (approximate) |
| Documented Substrates | Ceramic, Porcelain, Calibrated Stone (Wall Tiles) |
| Primer Guidance | None required for spacers |
| Classification | Non-Hazardous, Inert Plastic |
| Certifications | ISO 9001:2015 Manufacturing Process |
| Packaging | 500 Piece Bag, 1,000 Piece Bag, 2,000 Piece Bucket |
| Shelf Life | Unlimited (under normal conditions) |
| Reusable | Yes (if removed before adhesive cures) |